|
| |
FMC
Automotive 4-wheel Alignment System
Make a Bid!
This package includes
the following:
FMC 9909SE
Alignment Console
-
- Click on the "thumbnail" of a picture to enlarge it.
-
- This unit was
serviced and calibrated by EquiServ in January 2002
- It was updated to the
2001 vehicle specs.
- It has been in
storage since then and is ready for use.
-
- 4
head alignment with infrared optics.
- Includes
recalibration fixture for onsite head calibration.
- Each
head plugs directly into the
parallelogram sister racks internal wiring. No cables or
lines to trip over.
- The
9909SE was the FMC Alignment Flagship for over a decade. It is a bug free,
proven design.
- Field
service now performed nationally by EquiServ Equipment Repair. This is where
a number of the former FMC field techs went after FMC split their divisions
up.
- Those
same former FMC field technicians now working for EquiServ will tell you
they prefer to do alignment work with this unit over the newer ones.
- Alignment
specifications for this unit are software based and will continue to have
field upgradeable new vehicle alignment specifications available for years
to come.
FMC 4772 Parallelogram Alignment Lift
-
- Click on the "thumbnail" of a picture to enlarge it.
-
- 7000
lb. Capacity
- Maximum
4-wheel alignment wheelbase is 144”
- 65”
lifting height
- 20
different heights. All are level for alignment.
- Safety
locks at each height.
- Includes
turntables.
- Includes
rear-slip plates with locks.
- Includes
TWO model 98 roller jacks. (specs below)
- Includes
optional, internal, built-in alignment wiring.
- Built
in air connectors for tools and roller jacks.
- Built
in retractable work steps.
- Total
free access undercar between runways.
- Drive
on ramps.
- Pressure
safety valves protect against sudden line pressure loss.
- Hydraulic
cylinders are under runways and located off the floor.
- Above
ground installation.
- 3”
concrete with 3,000 psi rating. (Virtually every shops floor)
- 220v
single phase. 20-amp service.
- UL
listed.
- Shipping
weight approx. 4400 lbs.
- Bay size requirement: 27’6” by 12’
- .
- This unit has been
out of service and in storage. The ramp surfaces now have light rust from
disuse. If desired, we will
soda-blast the top ramp, on-ramps, slip plates and turntable tops to make ready for
you to repaint to your desired color.
Model 98 Roller
Jacks (per each)
-
- Click on the "thumbnail" of a picture to enlarge it.
-
- 5,000
lb. Capacity.
- 20.5”
lifting height.
- Frame
adapters.
- Drive-on
height is 3.25”
- Operates
with 120-psi air.
- Shipping
weight approx. 570 lbs.
PAYMENT:
- Credit Cards
accepted. As we have done on past auctions, we will fax you an invoice.
We ship immediately upon receipt of confirmed funds.
- We also offer commercial equipment
leasing to approved buyers.
WARRANTY:
Buyer pays freight
and/or crating expenses if it is to be containerized.
-
We will load on this end. Use our carrier or one
of yours.
-
These units are truckable/shippable anywhere in the
world. Total indicated weight of the above is approx. 6,000 lb.
-
I have shipped items like this before. My last shipment
was 4,000 lbs. and was trucked from Miami, FL to Portland, OR. Cost was
$1,150.00 (That is as coast to coast as you can get!)
-
This shipment should be around $1,500 to $1,750 or so
for that same distance coast to coast. Obviously, it should cost less if you
ship fewer miles.
Please contact us if you have any questions that you feel are not answered in
this listing or from the pictures.
Harmon
Distributing is located in Portland, OR.
We have served the automotive
aftermarket since 1983. References are available.
|
